loading
reading
writing
saving
searching
Modular Synth Components - $700 (Rockledge)
QR Code Link to This Post
Up for grabs are several modular synth components. The included modules are listed below. In addition to the modules, I’m also including essential accessories:
• 3U Eurorack case brackets
• 3U DIY Eurorack blank panels
• Patch cables
• Additional bus cables
Aside from the case itself, this is basically everything you need to start building a modular synth setup. Retail for all of this is over $1,200. I’m asking $700 for everything.
MST Dual Envelope – Retal: $164.99
The MST Dual Envelope is a simple-to-use yet complex dual envelope generator. Channels 1 and 2 are both normalled to each other to cycle when the other respective channel hits end of cycle, allowing for really interesting ping-pong effects. Each channel also has an end-of-cycle trigger output with LED indicator. There'¬s a normal and inverted envelope out. The inverted envelope out can be further modified by the +5 offset switch, which allows the inverted waveform to travel in the positive. The + output level allows the envelope signal to go between zero and the maximum voltage rail. Attenuate the output level down for a more subtle envelope (adjust to taste).
https://store.synthrotek.com/mst_dual_ad-asr_envelope
MST VC Low Pass Filter – Retal: $99.99
The MST Low Pass Filter is a precision analog dual slope output 2 & 4 pole filter. Simultaneous -12 DB and -24 DB outputs with CV control over all parameters. Can be used as a 1V/O sine wave oscillator.
https://store.synthrotek.com/mst_vc_low_pass_filter
MST Dual VCA – Retal: $119.99
The MST Dual 2164 VCA is a precision AC (audio) & DC (gate triggers or control voltage) Voltage Controlled Amplifier in 6HP. Each channel has a linear or exponential response switch, the exponential resulting in a poppier response. Adjustable output level and bleed if you want to mix in your unaffected source audio. Butters your toast all the way to the edge.
https://store.synthrotek.com/mst_dual_vca
MST VCO – Retal: $199.99
The MST VCO is a 100% analog 6-octave 1V/O trackable precision oscillator with full pulse width and modulation controls and with 5 waveform outputs.
https://store.synthrotek.com/mst_vco_voltage_controlled_oscillator
MST Midi to CV Converter – Retal: $164.99
The MST MIDI to CV Converter is a translator between digital devices and analog synths, allowing you to connect your modular system to a keyboard, computer, phone or tablet.
https://store.synthrotek.com/MST-MIDI-to-CV-Converter_p_500.html
MST 3U Sterio Output Mixer – Retal: $64.99
The MST Stereo Mixer is intended for pannable stereo output, but it is also suitable for both AC & DC voltage signals (Gates, Triggers and Control Voltage).
https://store.synthrotek.com/mst_stereo_output_mixer
Classic Noise. DLY Module (DIY Kit) – Retal: $82.99
The Synthrotek DLY is a PT2399 bucket-brigade delay module. The PT2399 IC delivers warm and lush analog-sounding tones (the IC is partially digital). The DLY is similar in tone to our ECHO Eurorack module, but its features make it unique in its own right. Unlike the ECHO which always has a wet signal (i.e. the output is always mixed in with the input), the DLY offers a true wet/dry Mix knob. When the Mix knob is fully counter-clockwise, you get a dry signal. When it is fully clockwise, you get a fully wet signal. This allows the user to plug this delay into effects loops. Also, the DLY allows for CV over Feedback and has an internal Feedback amount trimpot for precise adjustment.
https://store.synthrotek.com/dly_kit
Thumb Screws for Modules - Retal: $4.99
Throw away your screwdrivers! Eurorackers make it easy to pull modules in and out of your system at will. There is a philips option for those who want to torque their module screws to the original Doepfer standard of "gutentight."
https://store.synthrotek.com/eurorackers--thumb-screws-for-modules.html
Deluxe 10 Connection Flying Bus Cable - Retal: $14.99
The Deluxe 10 Connection Flying Bus Cable makes connecting power to your module a snap and a reality, especially if you have 10-pin powered module that has little room around the power pins. There are 10 Male Shrouded and Keyed Eurorack connectors for distributing power to your modules. There are also two keyed 16-pin female connectors for powering the cable and for daisy-chaining another flying bus cable (although you could connect this end directly to a module that takes 16-pin power (or 10 if there is room).
https://store.synthrotek.com/deluxe_10_connection_flying_bus_cable
Case Power: BLUE: +12V @ 3A; -12V @ 2.5A; +5V @ 1.5A (7312, UEI30) - Retal: $244.99
Case Power is a marriage of the 5A Power Supply System (now further regulating the +12V rail) and the Noise Filtering Distribution board, resulting in a love child called Case Power. It is safe, clean, quiet, and will power small and large Eurorack systems. Connecting Case Power to your current bus board system is easy with molex or spade connectors. We have 3U or 1U power entry panels available, but Case power doesn't have to take up valuable HP space; you can wire a jack, LED and switch into your case and easily attach them to the board.
https://store.synthrotek.com/Case-Power_p_585.html
Power Adapter / Brick – Retal: $24.99
This AC Power Adapter comes with a locking DC extension cable. The connector of the DC extension cable screws down to the DC jack, preventing noise interference when the cable is bumped.
https://store.synthrotek.com/Power-Adapter-Brick_p_365.html